1 - 1 - MODEL BE-70PS 70 NAME & NUMBER CALLER-ID TELEPHONE WITH SPEAKERPHONE OWNER’S MANUAL Please read this instruction manual c
11 - 11 - INSTALLATION - continued Setting the Display Language The display will show "SET LANGUAGE" as well as "E F S". The &
12 - 12 - INSTALLATION - continued 1. It is not necessary to enter the correct time and date when installing the telephone. 2. The correct time and da
13 - 13 - INSTALLATION - continued WALLWALLWall Mounting View Figure 8 Figure 7 Wall Mounting Bracket Telephone Cord Recess RJ-11W Jack Rear View
14 - 14 - INSTALLATION - continued 4. Install the telephone wall mounting bracket to the bottom surface of the telephone. See Figure 7 5. Plug the coi
15 - 15 - INSTALLATION - continued Figure 9 EXPANSION SELF-TAPPING ANCHOR SCREW Mounting Screw Mounting Screw 3
16 - 16 - OPERATION Using the Ringer Off/Low/Hi Switch The Off/Low/Hi switch can be used to set the sound level of the ringer. 1. Set the Off/Low/Hi s
17 - 17 - OPERATION - continued 1. Press the SPK button, the SPK LED will light. 2. Adjust the VOLUME control located on the right side of the telepho
18 - 18 - OPERATION - continued Storing Telephone Numbers into One Touch Memory Telephone numbers up to 16 digits can be stored in three one touch-mem
19 - 19 - OPERATION - continued Using Chain Dialing Chain dialing allows you to dial a variety of numbers that have been previ-ously stored into memor
20 - 20 - OPERATION - continued 4. The new call information is displayed for about 20 seconds after the last ring is received. 5. If the data received
3 - 3 - IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fi
21 - 21 - OPERATION - continued 4. Once you have reviewed all the new call records, the repeat call indicator will not be displayed. 5. When you have
22 - 22 - OPERATION - continued Using the Call Back feature The Call Back feature allows automatic dialing of the telephone number shown in the d
23 - 23 - CARE AND MAINTENANCE Your Caller-ID telephone has been designed to give years of trouble free ser-vice. It is a sensitive electromechanical
24 - 24 - TROUBLESHOOTING The display screen is blank. Possible causes of the problem are: 1. The battery needs to be replaced. No Dial Tone. Possibl
25 - 25 - FCC REQUIREMENTS Equipment Notes This equipment is registered with the Federal Communications Commission and is in compliance with Part 68 o
28 - 28 - 02A00
4 - 4 - BATTERY CAUTIONARY INSTRUCTIONS CAUTION - To Reduce the Risk of Fire or Injury to Persons, Read and Follow these Instructions. 1. Use only the
5 - 5 - TABLE OF CONTENTS Features ...6 Introduct
6 - 6 - FEATURES The BE-70PS with Caller-ID incorporates 70 name and number Caller-ID memories into a single line telephone for convenient use. 3-Lin
7 - 7 - INTRODUCTION Congratulations on your purchase of the BE-70PS Caller-ID speakerphone. The BE-70PS provides you with a variety of telephone feat
8 - 8 - CONTROL LOCATIONS Figure 1 1. Hook Switch 2. Handset Hanger Tab 3. NEW Call LED 4. DELETE Button 5. Speaker 6. Telephone Number Paper 7. F
9 - 9 - CONTROL LOCATIONS - continued TEL LINE23 Figure 4 Rear View Figure 2 Right Side View 19 20 21 24 RINGERLOWHILOWTPVOLUMEF
10 - 10 - INSTALLATION Battery Installation For Caller-ID operation, the BE-70PS requires one rectangular 9 volt battery (not included). To install or
Comments to this Manuals